Posted on 31 Jan, 2020, in Uncategorized
Can you help me improve VOIP in my network, I have around 20 ruckus switches that are connected to one core switch. Now, users are complaining that they have a problem with the voice quality, but I am not sure if it’s the network issue. Every phone port has trust dscp configured, can you let me know what else can I do from a network perspective to improve voip? Maybe qos configuration advice?
Posted on 30 Jan, 2020, in Uncategorized
Customer is trying to take configuration backup on ICX managed by vSZ from SZ WEB interface and it is failing
Posted on 27 Jan, 2020, in Uncategorized
I have a Lennar home with a Ruckus switch icx 7150-c12p, which is then hardwired to 2 different R510 APs. When I moved to this house, AT&T had installed the internet, they had installed their modem router combo, which was hard-wired to the Ruckus 7150. Yesterday I switched service to Spectrum and got their modem installed. I added my Netgear Nighthawk router to the modem and then took the Eth cable from AT&T modem-router and plugged into my router. I thought this would work seamlessly. I did not change anything else. So now it looks like, Spectrum modem -> Netgear router -> Ruckus switch. But unfortunately, this lead to APs not broadcasting my Wifi anymore, I could not connect to them. Then I connected a Eth cable to switch and checked internet connectivity with a laptop which works fine. I tried power cycle switch, router etc. I even unplugged POE cables for APs to power cycle them. None of this helped. Then after a while, I replugged my ATT router back to switch and everything started working again. I need to get rid of ATT service so I need to make this work but do not know-how. What could be done?TDLR- changed router from ATT to Netgear, APs not broadcasting any Wifi, only internet is with ETH cable from Switch.
Posted on 24 Jan, 2020, in Uncategorized
This is my first experience with any Ruckus product. Without going into too much unnecessary detail, I will need wireless access to my home network soon and have acquired a R500 that will hopefully fit the bill. It has the ZoneFlex Solo Access Point 110.0.0.0.675 loaded on it. Currently I have the basic home setup, some computers, ipads, TVs some IOT devices, etc that is wireless from my current setup (Calix 844g-1 provided by my ISP). I’m kind of hoping to VLAN some of this stuff out and have read that the Ruckus should fit the bill. My first real question, is this the software that I need to do what I’m looking to do or should I reconfigure? The second question is, would there be a better option (without breaking the bank)? Thanks in advance!!
Posted on 23 Jan, 2020, in Uncategorized
The Clearpass Policy Manager server requires attribute dictionary files be in .xml format.
This article contains a Ruckus VSA data dictionary file in .xml format for Aruba ClearPass server.
Posted on 22 Jan, 2020, in Uncategorized
Hi,I did understand that there is a two tier approach to upgrade the firmware to the latest UFI code.The recommended SW is:I assume the R means router image:SPR08090d.binSPR08090dufi.binI did not recieved the hardware yet, i plan to upgrade my customers campus with 5x 7150 in ring topology / (remote) stack configuration.Depending on the default sw, i would need to downgrade /upgrade to the 8080e code before attempting to upgrade to 8090 or 8092? We do not plan to use zone director, because customers campus is possibly to small for such requirement, then the 8092 is the most future proof image at this moment in time?The cusotmer may be interested in LAG groups, that is why he would need the router image, because that is a layer 3 feature – is that correct?Without the router image, the 7150 cant configure LAG on his access ports? Stacking /Trunking is not influenced by the choice of sw image (switch /router)?
Posted on 22 Jan, 2020, in Uncategorized
This article explains why we are unable to manage ICX switches with SZ cluster, and an error is observed, “Error: Failed to add new switch because of exceeding system capacity!” or Error: 21001: switch max capacity has been reached.
Posted on 22 Jan, 2020, in Uncategorized
As of Dec. 5, 2019, Ruckus Flexera Cloud License server for SZ/vSZ capacity licenses no longer supports TLS 1.0.
Posted on 21 Jan, 2020, in Uncategorized
HI, i am connecting my pc to a edge switch vlan and pinging to the core switch ip then i m getting latency in pinging. There is distribution switch in between core and edge switch. please let me know the reasons and how to solve it.
Posted on 21 Jan, 2020, in Uncategorized
The CLI ‘erase system factory-default’ command will reset an ICX switch.
Posted on 17 Jan, 2020, in Uncategorized
RUCKUS Unleashed R750 Access Point Quick Setup Guide (QSG).
Posted on 09 Jan, 2020, in Uncategorized
Good morningI have 2 ICX 7150 48P switches in stack.Image version SPS08080dBoot version mnz10114POE version icx7xxx_poe_02.1.0.b002In both switches the 1/1/1 to 1/1/8 ports are turned off.If I attack an AP the POE turns on the AP but does not pass the link.In any case, the 8-port LEDs do not light up.It can depend on thisBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableBCM_ERR: at /vobs/fdry/build/../../../../..///vobs/platform/HAL/driver/link/sdk_al/fdry_bcm_phy_al.c: 640 while ‘bcm_port_mdix_set’ is Feature unavailableWhat can I do?
Posted on 07 Jan, 2020, in Uncategorized
We recently purchased a smart home that has a Ruckus r510 AP installed in the ceiling of the front entryway, which is connected to a Ruckus ICX-7150 switch in a media cabinet in the laundry room. All the smart home features seem to be working pretty well — the only complaint I have is that there are a few “dead spots”, locations in the house where it seems to take forever to get my smartphone to communicate to the smart home devices through the supporting apps. I was wondering what options I might have to improve reception/range to try to eliminate these dead spots. I would not consider myself an expert on home Wi-Fi & networking, but I’m a quick study — I’m hoping for a fairly economical solution that would also minimizes the chances of me unintentionally crashing my smart home to a point where I can’t recover with my limited knowledge!
Posted on 06 Jan, 2020, in Uncategorized
Hi. I bought a Lennar home and it came pre-installed with Ruckus r510 and ICX 7150 C12P. I’m getting around 100 Mbps from speed tests while on the r510. However, on my Asus, I’m pulling around 580 Mbps. I believe the issue is that I’m uplinked from the r510 to the ICX at 100 Full. I can’t seem to change the NIC port speeds on my r510 to 1000 Mbps Full. Below are the CLI output from the r510 and ICX. The r510 is connected to port 1/1/1. Port 1/1/3 is uplink to my AT&T modem. I’m running 200.6.10.1.312 on the r510.telnet@ICX7150-C12 Switch#sh int briefPort Link State Dupl Speed Trunk Tag Pvid Pri MAC Name1/1/1 Up Forward Full 100M None No 1 0 c0c5.2093.a9431/1/2 Down None None None None No 1 0 c0c5.2093.a9441/1/3 Up Forward Full 1G None No 1 0 c0c5.2093.a9451/1/4 Down None None None None No 1 0 c0c5.2093.a9461/1/5 Up Forward Full 100M None No 1 0 c0c5.2093.a9471/1/6 Down None None None None No 1 0 c0c5.2093.a9481/1/7 Down None None None None No 1 0 c0c5.2093.a9491/1/8 Up Forward Full 100M None No 1 0 c0c5.2093.a94a1/1/9 Up Forward Full 100M None No 1 0 c0c5.2093.a94b1/1/10 Up Forward Full 100M None No 1 0 c0c5.2093.a94c1/1/11 Down None None None None No 1 0 c0c5.2093.a94d1/1/12 Down None None None None No 1 0 c0c5.2093.a94e1/2/1 Down None None None None No 1 0 c0c5.2093.a9501/2/2 Down None None None None No 1 0 c0c5.2093.a9511/3/1 Down None None None None No 1 0 c0c5.2093.a9521/3/2 Down None None None None No 1 0 c0c5.2093.a953mgmt1 Down None None None None No None 0 c0c5.2093.a943ruckus> enruckus# show configProtocol Mode= IPv4-OnlyDevice IP Address: Mode= DHCP IP Address= 192.168.1.70 Netmask= 255.255.255.0 Gateway Address= 192.168.1.254 Primary DNS= 192.168.1.254 Secondary DNS=Country Code: Code= United StatesIdentity: Name= Ruckus-UnleashedSession Statistics: Enable= false Limited Unauthorized Session= trueNTP: Status= Enabled Address= ntp.ruckuswireless.com Timezone= GMTLog: Status= Disabled Address= Facility= Priority= AP Facility= AP Priority= event log level= 1Bonjour Service: Status= EnabledTelnet Server: Status= DisabledFTP Server: Status= Enabled Anonynous Status= DisabledUnleashed Multi-Site Manager: Status= Disabled Address= Interval= 3login warning: Status= Disabled content= “Warning, you are logging into device for authorized user only. If yo u are not an authorized user, please click Quit; otherwise click Continue to log in.”LWAPP: MGMT queue length threshold to drop AUTH frame = 100 MGMT queue length threshold to resume processing AUTH frame = 25EAPoL Key no Retry: Status= DisabledUnleashed Network: Token= un1619020082171532588476075AAA: ID: 1: Name= Local Database Type= Local 2: Name= Guest Accounts Type= GuestDHCP servers for DHCP relay agent:Administrator Name/Password: Name= admin Password= Authenticate: Mode= Authenticate using the admin name and passwordManagement ACL:AP: ID: 1: MAC Address= 1c:3a:60:36:ae:d0 Model= r510 Approved= Yes Device Name= RuckusAP Device Role= Master Description= Location= GPS= CERT = Normal Bonjour-policy= Bonjour-fencing= Group Name= System Default Channel Range: A/N= 36,40,44,48,149,153,157,161 (Disallowed= ) B/G/N= 1,2,3,4,5,6,7,8,9,10,11 (Disallowed= ) Radio a/n: Channelization= Auto Channel= Auto WLAN Services enabled= Yes Tx. Power= Auto WLAN Group Name= Default Call Admission Control= OFF Protection Mode= Auto Radio b/g/n: Channelization= Auto Channel= Auto WLAN Services enabled= Yes Tx. Power= Auto WLAN Group Name= Default Call Admission Control= OFF Protection Mode= 2 Override global ap-model port configuration= No Network Setting: Protocol mode= IPv4-Only Device IP Settings= DHCP IP Address= 192.168.1.70 Netmask= 255.255.255.0 Gateway= 0.0.0.0 Primary DNS Server= 192.168.1.254 Secondary DNS Server= Mesh: Status= Disabled LLDP: Status = Use Parent Setting LAN Port: 0: Interface= eth0 Dot1x= None LogicalLink= Up PhysicalLink= Up 100Mbps full Label= 10/100/1000 PoE Port1 1: Interface= eth1 Dot1x= None LogicalLink= Down PhysicalLink= Down Label= 10/100/1000 Port2 PoE Mode= AutoSmart Redundancy: Status= Disabled Peer IP/IPv6 Address= Shared Secret=IPv4 Management Interface: Status= Disabled IP Address= Netmask=L2/MAC ACL: ID: 1: Name= System Description= System Restriction= Deny only the stations listed below Stations:SNMP Agent: Status= Disabled Contact= Location= RO Community= public RW Community= privateSNMP Trap: Format= Version2 Status= DisabledSNMPV3 Agent: Status= Disabled Ro: User= Authentication Type= MD5 Authentication Pass Phrase= Privacy Type= DES Privacy Phrase= Rw: User= Authentication Type= MD5 Authentication Pass Phrase= Privacy Type= DES Privacy Phrase=SNMP Trap: Format= Version3 Status= DisabledWLAN Service: ID: 1: NAME = House14 Tx. Rate of Management Frame(2.4GHz) = 2.0Mbps Tx. Rate of Management Frame(5GHz) = 6.0Mbps Beacon Interval = 100ms SSID = House14 Description = House14 Type = Standard Usage Authentication = open Encryption = wpa2 Algorithm = aes Passphrase = FT Roaming = Disabled 802.11k Neighbor report = Disabled Web Authentication = Disabled Authentication Server = Disabled Accounting Server = Disabled Called-Station-Id type = wlan-bssid Tunnel Mode = Disabled DHCP relay = Disabled Max. Clients = 100 Isolation per AP = Disabled Isolation across AP = Disabled Zero-IT Activation = Disabled Load Balancing = Enabled Band Balancing = Enabled Dynamic PSK = Disabled Auto-Proxy configuration: Status = Disabled Inactivity Timeout: Status = Disabled VLAN-ID = 1 Dynamic VLAN = Disabled Closed System = Disabled Https Redirection = Disabled OFDM-Only State = Disabled Multicast Filter State = Disabled 802.11d State = Disabled Force DHCP State = Disabled Force DHCP Timeout = 0 DHCP Option82: Status = Disabled Option82 sub-Option1 = Disabled Option82 sub-Option2 = Disabled Option82 sub-Option150 = Disabled Option82 sub-Option151 = Disabled Ignore unauthorized client statistic = Disabled STA Info Extraction State = Enabled BSS Minrate = Disabled DTIM period = 1 Directed MC/BC Threshold = 5 Call Admission Control State = Disabled PMK Cache Timeout= 720 minutes PMK Cache for Reconnect= Enabled NAS-ID Type= wlan-bssid Roaming Acct-Interim-Update= Disabled PAP Message Authenticator = Enabled Send EAP-Failure = Disabled L2/MAC = No ACLS L3/L4/IP Address = No ACLS L3/L4/IPv6 Address = No ACLS Precedence = No ACLS Proxy ARP = Disabled Device Policy = No ACLS Vlan Pool = No Pools Role based Access Control Policy = Disabled SmartRoam = Disabled Roam-factor = 1 White List = No ACLS Application Recognition & Control = Disabled Apply ARC Policy = NO POLICY Client Flow Data Logging = Disabled Wlan Bind = allWLAN Group: ID: 1: Name= Default Description= Default WLANs for Access Points WLAN Service: WLAN1: NAME= House14 VLAN=
Posted on 04 Jan, 2020, in Uncategorized
We Need Ruckus help Regarding password Reset :1.While the recover the forgot password device configuration should not erase.