Posted on 31 Jul, 2019, in Uncategorized
Hello,I’d like to ask if ICX-7150 switches do support Layer3+4 hash algorithm in LACP/LAG. I’m connecting them to linux servers (2-4 NICs) using 802.3ad bonding. I tested Layer2+3 and Layer3+4 xmit_hash_policy on linux and traffic seems to be working fine but I’d like to be sure that switches fully support the Layer3+4 hashing?Thank You in advanceBest Regards!
Posted on 30 Jul, 2019, in Uncategorized
We have an ICX7750 with 48 port 10G module. All clients connect at 10G no problem.The same clients – Mac High Sierra & Windows 10 – when connected to our ICX7450 with ICX7400 module, only achieve 5G speeds. The module is recognised ok by the switch, and the ports are running at 10G Full. Auto neg is not available on these ports – I think they only run at 10G.
Posted on 25 Jul, 2019, in Uncategorized
Observing the following log message on ZD – ” AP[Ruckus 1] detects excessive probe requests on radio [11b/g] “
Posted on 25 Jul, 2019, in Uncategorized
This article describes Ruckus Cloud Wi-Fi resources and FAQs for Customers
Posted on 25 Jul, 2019, in Uncategorized
This bulletin covers a problem and corrective actions to address incorrectly programmed SIMs for Ruckus private LTE network service.
Posted on 24 Jul, 2019, in Uncategorized
Customer replaced HP switches with ICX7150 and started experiencing communication issues with Microsoft NLB
Posted on 24 Jul, 2019, in Uncategorized
By current design, all configured RADIUS-servers are used for SSH/Telnet/Console authentication. Therefore, users that have access to the network can login into the switch using their credential, which is a security concern for our customers.
Posted on 24 Jul, 2019, in Uncategorized
Downgrading code from FI 08.0.50 will result in ACL loss from config
Posted on 24 Jul, 2019, in Uncategorized
We have CLI commands to configure Telnet or Console session timeout periods.
Posted on 24 Jul, 2019, in Uncategorized
When 3m passive cables used on 7150 to form stack, the stack is unstable and port flap is seen.
Posted on 18 Jul, 2019, in Uncategorized
Ruckus ICX FastIron developers and Quality Assurance are pleased to announcea new FI 08.0.91 (GA) firmware release for ICX 7150, 7250, 7450, 7650, 7850 modelswitches. Three new models of ICX-7150(-24F, -C10ZP, -C08P) are supported, andalso Ansible support for automation.
Ruckus ICX FastIron 08.0.91 (GA) Release Notes:
https://support.ruckuswireless.com/documents/2884-ruckus-icx-fastiron-08-0-91-ga-release-notes
Ruckus ICX FastIron 08.0.91 (GA) Software Release (.zip):
https://support.ruckuswireless.com/software/2141-ruckus-icx-fastiron-08-0-91-ga-software-release-zip
Posted on 18 Jul, 2019, in Uncategorized
Hi, Does Brocade ICX multilayer switches have NAT configuration capability? Can someone provide me the configuration for my guide or the equivalent of this to Cisco? Thank you very much.Regards,Jam
Posted on 12 Jul, 2019, in Uncategorized
When using 8.0.90 you can use the newly introduced copy manifest command, but it only works when TFTP client in the ICX switch is disabled.
Posted on 12 Jul, 2019, in Uncategorized
How to debug “soft lockup” error
Posted on 08 Jul, 2019, in Uncategorized
Ruckus APs can provide DHCP/NAT features in Solo AP, wired Unleashed Master, and SZ 3.5+ zone Access Points.