Posted on 23 Dec, 2019, in Uncategorized
Hello,i have an Problem: When i create an User over Telnet Console the secondary stack member does simply restarts. Is that normal?I have two ICX7250-24 with 08070e (Switch – Layer2) Firmware Version.On that version is it possible to enable SSH?regards
Posted on 19 Dec, 2019, in Uncategorized
I have an ICX 7150-C12P. The power was out for several hours and when it came back on the PoE wasn’t active. I have done the factory reset about a dozen times and I can’t get it back. I’ve read all these complex instructions on finding IP address, using a terminal prompt etc etc etc. Unfortunately all of that is over my head. Is there a way to manually turn it back on? Any help is greatly appreciated.
Posted on 19 Dec, 2019, in Uncategorized
Is support planned for DHCPv6 server in the ICX line? The ability to run DHCPv6 on the switch to hand out options is quite valuable, especially in a SLAAC environment.I’m configuring some ICX 7650 switches to replace a Catalyst 3750-X stack and am disappointed that I can’t supply IPv6 DNS and NTP server information from a built-in DHCP server as I could on the Cisco boxes.
Posted on 17 Dec, 2019, in Uncategorized
I will be decommissioning and removing copper connection in couple of weeks. Instead of doing cutover migration using eth 0. I decided to setup eth4 for Fiber and with the help of support team I set the interface for external network with new public IP and setup it up as primary interface on a failover setting. so all DNS and policy that uses will continue using copper and gradually modify policy and 1to1 NAT and SNAT.I have brocade 6610 layer three switch which has vlan 2001 for public ethernet. Copper port on switch was set to dual-mode on 2001 only and did not have association with default vlan 1.While I was trying to create fiber with similar switch configuration I ended up setting fiber dual-mode with vlan membership of 2001 (tab), 1 and 200. I was able to remove vlan 200 which did not cause any issue but as soon as I remove vlan 1 and set dual mode 2001 only interface fails which is exactly same as copper. Not sure if switch need to be rebooted to fix it. But again as soon as I put it back on 1 and 2001 with dual mode it works fine so I assume firewall is seeing change from switch which means it should not require reboot to trickle the change.Not sure why it does not work when I only try to associate to 2001 vlan which is set for public gateway. it is working fine on copper but fiber only works when traffic is routed from default vlan 1. Default vlan 1 is not best recommended vlan for any interface
Posted on 13 Dec, 2019, in Uncategorized
Ruckus Networks supports Smart Home technology, and we have partners who are installing packages with an ICX-7150 switch, one or two R510 Unleashed APs, and instructions for using the UMA (Unleashed Mobile App) to setup, monitor, and manage wireless networks in new homes. In support of this design, we have compiled a page with Knowledge Base Articles, Videos, and links called Ruckus at Home, on our Support portal’s How-to-Hub.https://support.ruckuswireless.com/hth-ruckus-at-homeThere is also a new Ruckus at Home Forum group for members to discuss ideas and issues openly, and to share tips/advice.https://forums.ruckuswireless.com/ruckuswireless/categories/ruckuswireless_ruckus_at_homeYou may have been pointed to these sites by your Smart Home installers, or as a package by Ruckus Value Added Resellers,and we invite all interested Unleashed, ICX Switching/Routing, and Mobile Application users to participate in this forum as well.
Posted on 12 Dec, 2019, in Uncategorized
I have a icx7750 switch in a datacenter as routing device. Everything was running fine, but since we merge with a new organization, response time of the switch is very bad (ssh lag in cli) and we are now losing communication randomly with some servers behind. We added 4 access switch and 19 new router-interface ve (previously 2 switch and 49 interface ve).cpu and memory dont seems to be a problemcan a system parameters was not set correctly (see below)?thanksSSH@R0202000-DISTR-CT-RT-01#sh default valuessys log buffers:50 mac age time:300 sec telnet sessions:5ip arp age:10 min bootp relay max hops:4 ip ttl:64 hopsip addr per intf:24when multicast enabled :igmp group memb.:260 sec igmp query:125 sec hardware drop: enabledwhen ospf enabled :ospf dead:40 sec ospf hello:10 sec ospf retrans:5 secospf transit delay:1 secwhen bgp enabled :bgp local pref.:100 bgp keep alive:60 sec bgp hold:180 secbgp metric:10 bgp local as:1 bgp cluster id:0bgp ext. distance:20 bgp int. distance:200 bgp local distance:200System Parameters Default Maximum Current Configuredip-arp 8192 64000 8192 8192ip-static-arp 512 1024 512 512ip-cache 8192 32768 8192 8192ip-filter-port 2047 2047 2047 2047ip-filter-sys 3072 8192 8192 8192l3-vlan 32 1024 32 32ip-qos-session 1024 16000 1024 2048mac 32768 32768 32768 32768ip-route 98304 131072 98304 98304ip-static-route 64 2048 64 64vlan 64 4095 1024 1024spanning-tree 128 254 128 128mac-filter-port 32 256 32 32mac-filter-sys 64 512 64 64ip-subnet-port 24 128 24 24session-limit 65536 160000 65536 65536view 10 65535 10 10virtual-interface 255 512 255 255hw-ip-next-hop 17408 17408 17408 17408hw-traffic-condition 50 1024 50 50rmon-entries 2048 32768 2048 2048igmp-snoop-mcache 512 6144 512 512mld-snoop-mcache 512 6144 512 512ip6-route 5120 7168 5120 5120ip6-static-route 64 1024 64 64ip6-cache 1024 2048 1024 1024msdp-sa-cache 4096 8192 4096 4096gre-tunnels 16 64 16 16ip-vrf 128 128 128 128ip-route-default-vrf 65536 131072 8000 8000ip6-route-default-vr 2048 7168 2048 2048ip-route-vrf 4096 131072 4096 4000ip6-route-vrf 1024 7168 1024 1024pim-hw-mcache 1024 6144 1024 1024pim6-hw-mcache 512 2048 512 512igmp-snoop-group-add 4096 8192 4096 4096mld-snoop-group-addr 4096 8192 4096 4096mac-notification-buf 4000 16000 4000 4000openflow-flow-entrie 3072 3072 3072 3072openflow-pvlan-entri 40 40 40 40openflow-unprotected 40 40 40 40max-ecmp 8 32 8 8max-dhcp-snoop-entri 1024 3072 1024 1024max-static-inspect-a 512 1024 512 512
Posted on 11 Dec, 2019, in Uncategorized
I tried to upload image for ICX7150-C12-POE and it was succesfulBut when i show version, I saw information as belowBYT-Ruckus-Spare#show version Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved. UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a (24723488 bytes) from Primary SPR08090c.bin SW: Version 08.0.61aT211 Compressed Boot-Monitor Image size = 786944, Version:10.1.15T225 (mnz10115) Compiled on Thu Jan 31 07:08:55 2019 Please have a look at the line”UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a (24723488 bytes) from Primary SPR08090c.bin”Something wrong hereCould you give me advice this case please??Thank you very much
Posted on 10 Dec, 2019, in Uncategorized
We have a large campus network: ZoneDirector ZD1200, ± 50 AP’s R500 and R510, ± 100 Apple TV’s, lots of iPads (1:1 and shared iPads). The Apple TV’s and iPads are on the same SSID, but in small VLAN’s/subnets. The backbone of our network has high performance. WiFi speed and reliability are perfect.We use AirPlay mirroring to the Apple TV’s to cast the screen of the teachers iPads to the projector or TV screen. We don’t use Bonjour Gateway. From time to time, we experience drop outs or lag in the Airplay streaming. We’d like to know, when configuring a WiFi network for AirPlay with lots of Apple TV’s:What are the best WLAN settings?What are the best settings for things like self healing, background scanning, load balancing, etc…?What are the best settings for the AP’s?Any other best practices to make AirPlay reliable?Any help or advice is greatly appreciated.
Posted on 10 Dec, 2019, in Uncategorized
ICX 7150 and ICX 7650 switches do not retain clock date and time after power outage
Posted on 10 Dec, 2019, in Uncategorized
How to configure and troubleshoot Ruckus Bonjour Gateway in ZD and vSZ/SZ-100/SCG
Posted on 02 Dec, 2019, in Uncategorized
There is a standard OID example that can be used to find the MAC address of end devices plugged into the ICXs’
Posted on 02 Dec, 2019, in Uncategorized
This article explains on changes made and inter-working of Anti-spoofing feature with Client Isolation
Posted on 01 Dec, 2019, in Uncategorized
We are using the ICX 7250 switch in combination with data diodes and for that reason we need multicast to be enabled. But when I enable the multicast via the web interface of the ICX 7250, it disables itself after applying. Is there a trick or firmware update needed ?