Posted on 30 Jan, 2019, in Uncategorized
Ruckus Wireless Unleashed 200.7.10.2.339 (GA) Quick Setup Guide (M510).View Unleashed 200.7 Online Help Admin Guide at this Link.
Posted on 28 Jan, 2019, in Uncategorized
Hello everyone,I want to help my friend to rebuild fairly large (in the sense of surface) hotspot network in hotel. Everything is set (captive portal, radius) aside of APs.I can buy, fairly cheap, old Ruckus hardware (Zoneflex 7363,7962,7942,7352 etc) and here is the question:will they work as simple dumb APs, just for spreading wifi all over?All i need is wifi ap with poe power. I have heard they have very good redios with decent antenas and are pretty solid in general.i know there are a lot of old hardware, but usually they need some sort of controller (MERU,TRAPEZE etc).Best regards
Posted on 28 Jan, 2019, in Uncategorized
How can I discover the Ruckus ZoneDirector so I can use a Web browser to see the Web UI?
Posted on 28 Jan, 2019, in Uncategorized
Version 100.1.0.9.46 appears to have problem passing VTP between Cisco switches on both sides, fixed with a bug patch.
Posted on 27 Jan, 2019, in Uncategorized
How to see or edit AP properties – Ruckus Wireless Airmagnet planner
Posted on 27 Jan, 2019, in Uncategorized
This article describes the impact of applying a positive or negative leap second to Ruckus hardware.
Posted on 27 Jan, 2019, in Uncategorized
Please I need a confirmation if Ruckus Zone Planner supports floor plans in PDF format? I can’t import PDF files.
Maybe I need to do an upgrade to be able to use PDF files. Please help.
Posted on 26 Jan, 2019, in Uncategorized
Longtime user of Ruckus AP’s, but new to the ICX switches. I’ve been using the ICX Switches in test-bench scenarios to see how I like them before deploying them wide spread. I apologize for what may seem a simple question, but I am just not getting this to work.I have a single ruckus AP, 510 Unleashed, and they have two SSID’s tagged on two separate VLAN’s, so within the AP Test1 tagged on VLAN 1, and Test2 tagged on VLAN 2.I’m currently using a 12 port ICX 7150 switch. My gateway is feeding into port 1/2/1 on the switch, and my AP is plugged into 1/1/11. I have my Management VLAN as 10, and I have VLAN 1 & VLAN 2 by port set up. In the Switch both VLAN 1 & 2 have 1/1/11 Tagged and 1/1/11 is set to dual-mode, and inline power is enabled. VLAN 1 & 2 also both have 1/2/1 tagged, and it is also set to dual-mode.When connecting wirelessly, SSID Test1 works great and I pull IP information, but Test2 does not seem to be passing info back to the gateway, as I do not properly pull an IP.I can see the gateway from any computer plugged into an untagged port associated with either vlan. I have set this same function up on other switches (though I’m not as proficient with CLI – I’m trying to get better), so I’m sure it’s possible. What am I missing? I feel like I’m super close to figuring this out. Thanks!
Posted on 24 Jan, 2019, in Uncategorized
Hi all,I’ve got an ICX6610 running router code that I’m currently using as my core switch with various VLANs. I’m trying to create a one-directional VLAN so that clients inside that VLAN cannot initiate connections out but other clients in other VLANs can connect to clients within. So far I’ve been going down the route of ip access-lists but hitting dead ends. Every time I apply an access list I lose connectivity both directions to the VLAN I’m trying to isolate. Does anyone have any recommendations or ideas that could help?Thank you!Rich
Posted on 24 Jan, 2019, in Uncategorized
Cat6A cable is recommended for 10GBASE-T speeds up to 100 meters for port aggregation on ICX 7650-48ZP.
Posted on 22 Jan, 2019, in Uncategorized
I have a gateway router which connects to a Ruckus ICX switch (running the Router image), which in turn has two Ruckus Unleashed APs connected to it.I would like to configure a wireless network which cannot access devices on my LAN, but which CAN be reached and managed by a device on my LAN. These would be untrusted IoT devices that run services which need to be accessible, but which do not need to initiate connections to other systems.I’m thinking the Unleashed AP ACLs aren’t granular enough for this type of configuration, and I’d instead need to configure a VLAN and implement a Firewall somewhere along the path.Is there a way to achieve this configuration with the equipment that’s already in place?Thanks in advance!
Posted on 21 Jan, 2019, in Uncategorized
How to configure DHCP scope on Juniper switch/router for Ruckus controller managed APs
Posted on 21 Jan, 2019, in Uncategorized
Provide details of OKC in action during a STA roaming event – how does this work prior to 802.11r support in SW.
Posted on 21 Jan, 2019, in Uncategorized
What information I need to provide when contacting Ruckus Wireless technical support when there is an FM issue?