Posted on 28 Mar, 2018, in Uncategorized
I’ve installed a couple of Ruckus ICX 7150 switches with no configuration and I would like to configure them remotely but when I ssh in, it wants a password which I never set. Suggestions?
Posted on 28 Mar, 2018, in Uncategorized
Wireless clients move around and are always sending probes and association requests. If not sending authentication with these, Ruckus APs may send de-auth packets.
Posted on 21 Mar, 2018, in Uncategorized
Hi,I’m trying to setup two ICX-7150. First I configure a certificate, a ssh-key and a user.I can login using a web browser or a serial connection, but ssh fails.A password prompt is shown, I get connected (the session prompt is shown), but the session is terminated immediately.Any idea ?
Posted on 21 Mar, 2018, in Uncategorized
We have ICX 7450 switch as distribution switch and below that we have 5 nos HP 5120 as access switches in a Ring Topology. We have connected one port of 7450 to HP Access switch one and another is connected to access switch 5. If i connect both the link i found STP loop and if i disconnected one of the link, the network found stable. Earlier it was Cisco switch and now we are replacing the same with Brocade.Please suggest.
Posted on 20 Mar, 2018, in Uncategorized
Posted on 09 Mar, 2018, in Uncategorized
when trying to create Virtual Routing interface for vlan I receive this errorLPK-ICX6610-01(config)#LPK-ICX6610-01(config)#vlan 100LPK-ICX6610-01(config-vlan-100)#router-interface ve 100Invalid input -> router-interface ve 100Type ? for a listLPK-ICX6610-01(config-vlan-100)#——————————————————————————–show run outputLPK-ICX6610-01(config)#sh run running-config Current running-configLPK-ICX6610-01(config)#sh running-configCurrent configuration:!ver 08.0.10gT7f1!stack unit 1 module 1 icx6610-24-port-management-module module 2 icx6610-qsfp-10-port-160g-module module 3 icx6610-8-port-10g-dual-mode-module stack-trunk 1/2/1 to 1/2/2 stack-trunk 1/2/6 to 1/2/7 stack-port 1/2/1 1/2/6stack enable!!!!vlan 1 name DEFAULT-VLAN by port!vlan 10 name LANUSER_GF by port tagged ethe 1/1/3!vlan 20 name LANUSER_1F by port!vlan 100 name WLAN by port tagged ethe 1/1/23 to 1/1/24 untagged ethe 1/1/12!!!!hostname LPK-ICX6610-01no ip dhcp-client enableip dhcp-server enable!ip dhcp-server pool vlan_100 dhcp-default-router 192.168.100.254 dns-server 1.9.1.9 8.8.8.8 excluded-address 192.168.100.1 192.168.100.10 lease 0 12 0 network 192.168.100.0 255.255.255.0 deploy!!!!!!!!!!!endLPK-ICX6610-01(config)#sh ver version System statusLPK-ICX6610-01(config)#sh version Copyright (c) 1996-2014 Brocade Communications Systems, Inc. All rights reserved. UNIT 1: compiled on Dec 17 2014 at 18:25:28 labeled as FCXS08010g (7280225 bytes) from Primary /FCXS08010g.bin SW: Version 08.0.10gT7f1 Boot-Monitor Image size = 370695, Version:10.1.00T7f5 (grz10100) HW: Stackable ICX6610-24==========================================================================UNIT 1: SL 1: ICX6610-24 24-port Management Module Serial #: BXP3843N00B License: BASE_SOFT_PACKAGE (LID: dzrINJIpFFd) P-ENGINE 0: type E02B, rev 01==========================================================================UNIT 1: SL 2: ICX6610-QSFP 10-port 160G Module==========================================================================UNIT 1: SL 3: ICX6610-8-port Dual Mode(SFP/SFP+) Module========================================================================== 800 MHz Power PC processor 8544E (version 0021/0023) 400 MHz bus65536 KB flash memory 512 MB DRAMSTACKID 1 system uptime is 1 hours 54 minutes 55 secondsThe system : started=cold start
Posted on 08 Mar, 2018, in Uncategorized
Hi,We are using two stacked ICX6610 switches and have several servers and storage connected to it. We have observed problems on our 10G ports – on server site (vmware esx hosts) we see constant link down/up events, and on storage ports we have CRC errors and port flapping condition. No errors are found on 1Gb ports, no flapping, no CRC, no link state changes.Sometimes we even get to APD event on vmware (we use 10G for NFS connection hosts<->storage).FastIron version used is 08.0.10g.Brief description (excluding 1G network connections):3 ESX hosts named host1, host2, host3 are connected to 10G ports.host1 – ports 1/3/3 and 2/3/3host2 – ports 1/3/4 and 2/3/4host3 – ports 1/3/5 and 2/3/5No teaming on hosts side – only virtual port based load balancing on virtual switches.Backup server is connected to ports 1/3/6 and 2/3/6. Here we use NIC teaming at server side (static link aggregateion) and switch side – LAG.Storage is connected to ports 1/3/1 & 2/3/1 and uses LAG.From one stack member there is only one active uplink to rest of network – port 1/1/24.I have copy-pasted our switch config below including port descriptions. Does anybody see some error in configuration?ICX6610-S-1>show configuration!Startup-config data location is flash memory!Startup configuration:!ver 08.0.10gT7f1!stack unit 1 module 1 icx6610-24-port-management-module module 2 icx6610-qsfp-10-port-160g-module module 3 icx6610-8-port-10g-dual-mode-module stack-trunk 1/2/1 to 1/2/2 stack-trunk 1/2/6 to 1/2/7 stack-port 1/2/1 1/2/6stack unit 2 module 1 icx6610-24-port-management-module module 2 icx6610-qsfp-10-port-160g-module module 3 icx6610-8-port-10g-dual-mode-module stack-trunk 2/2/1 to 2/2/2 stack-trunk 2/2/6 to 2/2/7 stack-port 2/2/1 2/2/6stack enablestack mac 609c.9f47.ee38!!!lag “storage2_10g_ports” static id 6 ports ethernet 1/3/2 ethernet 2/3/2 primary-port 1/3/2 deploy!lag “storage1_10g_ports” static id 2 ports ethernet 1/3/1 ethernet 2/3/1 primary-port 1/3/1 deploy!lag “BackupServer_10g_ports” static id 1 ports ethernet 1/3/6 ethernet 2/3/6 primary-port 1/3/6 deploy!!vlan 1 name DEFAULT-VLAN by port!vlan 6 by port tagged ethe 1/1/4 to 1/1/9 ethe 1/1/24 ethe 2/1/4 to 2/1/9!vlan 7 by port tagged ethe 1/1/4 to 1/1/9 ethe 1/1/24 ethe 2/1/4 to 2/1/9 untagged ethe 1/1/19 to 1/1/20 ethe 2/1/19 to 2/1/20!vlan 110 name ManagementNetwork by port tagged ethe 1/1/4 to 1/1/9 ethe 1/1/24 ethe 2/1/4 to 2/1/9 untagged ethe 1/1/1 to 1/1/3 ethe 1/1/10 to 1/1/12 ethe 2/1/1 to 2/1/3 ethe 2/1/10!vlan 111 name ServersNetwork by port tagged ethe 1/1/4 to 1/1/9 ethe 1/1/24 ethe 2/1/4 to 2/1/9 untagged ethe 1/1/13 ethe 2/1/11 to 2/1/13!vlan 112 name StorageNetwork by port tagged ethe 1/3/1 to 1/3/5 ethe 2/3/1 to 2/3/5 untagged ethe 1/3/6 ethe 2/3/6!vlan 113 name vMotionNetwork by port tagged ethe 1/3/3 to 1/3/5 ethe 2/3/3 to 2/3/5!vlan 155 name Servers2network by port tagged ethe 1/1/4 to 1/1/9 ethe 1/1/24 ethe 2/1/4 to 2/1/9!!!!aaa authentication web-server default localaaa authentication enable default localaaa authentication login default localjumboenable super-user-password …..enable aaa consolehostname ICX6610-S-1ip address xxx.xxx.xxx.xxx 255.255.255.0no ip dhcp-client enableip default-gateway xxx.xxx.xxx.xxx!logging host xxx.xxx.xxx.xlogging persistenceno telnet servertelnet server enable vlan 111username admin password …..cdp run!!clock summer-timeclock timezone gmt GMT+01!!ntp server x.x.x.x minpoll 5 burst!!web-management httpshitless-failover enableinterface ethernet 1/1/4 port-name host01 slot2 port0 vmnic6!interface ethernet 1/1/5 port-name host01 slot3 port0 vmnic8!interface ethernet 1/1/6 port-name host02 slot2 port0 vmnic6 spanning-tree 802-1w admin-edge-port!interface ethernet 1/1/7 port-name host02 slot3 port0 vmnic8 spanning-tree 802-1w admin-edge-port!interface ethernet 1/1/8 port-name host03 slot2 port0 vmnic6 spanning-tree 802-1w admin-edge-port!interface ethernet 1/1/9 port-name host03 slot3 port0 vmnic8 spanning-tree 802-1w admin-edge-port!interface ethernet 1/1/11 spanning-tree 802-1w admin-edge-port!interface ethernet 1/1/22 port-name “VLAN 110 uplink to cisco port X – disconnected cable”!interface ethernet 1/1/23 port-name “VLAN 111 uplink to cisco port X – disconnected cable”!interface ethernet 1/1/24 port-name “Uplink port to central Cisco”!interface ethernet 1/3/1 speed-duplex 10G-full!interface ethernet 1/3/2 speed-duplex 10G-full spanning-tree 802-1w admin-edge-port!interface ethernet 1/3/3 port-name saphost01 slot0 port0 vmnic2 speed-duplex 10G-full!interface ethernet 1/3/4 port-name host02 slot0 port0 vmnic2 speed-duplex 10G-full spanning-tree 802-1w admin-edge-port!interface ethernet 1/3/5 port-name host03 slot0 port0 vmnic2 speed-duplex 10G-full spanning-tree 802-1w admin-edge-port!interface ethernet 1/3/6 speed-duplex 10G-full spanning-tree 802-1w admin-edge-port!interface ethernet 1/3/7 speed-duplex 10G-full!interface ethernet 1/3/8 speed-duplex 10G-full!interface ethernet 2/1/4 port-name host01 slot2 port1 vmnic7!interface ethernet 2/1/5 port-name host01 slot3 port1 vmnic9!interface ethernet 2/1/6 port-name host02 slot2 port 1 vmnic7 spanning-tree 802-1w admin-edge-port!interface ethernet 2/1/7 port-name host02 slot3 port1 vmnic9 spanning-tree 802-1w admin-edge-port!interface ethernet 2/1/8 port-name host03 slot2 port1 vmnic7 spanning-tree 802-1w admin-edge-port!interface ethernet 2/1/9 port-name host03 slot3 port1 vmnic9 spanning-tree 802-1w admin-edge-port!interface ethernet 2/3/3 port-name host01 slot1 port1 vmnic5 speed-duplex 10G-full!interface ethernet 2/3/4 port-name host02 slot1 port1 vmnic5 speed-duplex 10G-full spanning-tree 802-1w admin-edge-port!interface ethernet 2/3/5 port-name host03 slot1 port1 vmnic5 speed-duplex 10G-full spanning-tree 802-1w admin-edge-port!!!!lldp run!!!!endICX6610-S-1>
Posted on 08 Mar, 2018, in Uncategorized
My AP server list is empty
Posted on 07 Mar, 2018, in Uncategorized
How to upgrade POE firmware on FastIron switches using BNA?
Posted on 07 Mar, 2018, in Uncategorized
Installing PoE firmware with TFTP – Brocade Campus Network Switches
Posted on 06 Mar, 2018, in Uncategorized
Steps to reproduce.
Posted on 06 Mar, 2018, in Uncategorized
How to disable the automatic reporting of information back to Ruckus
Posted on 05 Mar, 2018, in Uncategorized
When new ZD Ip is entered in browser, it will be redirected to HTTPS page with old Ip.
Posted on 01 Mar, 2018, in Uncategorized
hello Newbie question.I am trying to connect a ZD1200 via an ICX 7150 switch to H510 APs. vlan 1 is native /Vlan 20 public ssid /Vlan 30 for members / Vlan 40 for media and Vlan 100 for wired connections.I have the following config but unable to get the ZD on port 1/1/1 to connect to the APs on ports 1/1/3 – 1/1/12.The source internet port is 1/2/1——————————————————————-!ver 08.0.61aT213!stack unit 1 module 1 icx7150-24p-poe-port-management-module module 2 icx7150-2-copper-port-2g-module module 3 icx7150-4-sfp-plus-port-40g-module!!!!!vlan 1 name DEFAULT-VLAN by port!vlan 10 by port tagged ethe 1/1/1 ethe 1/1/11!vlan 20 by port tagged ethe 1/1/1 ethe 1/1/3 router-interface ve 20!vlan 30 by port tagged ethe 1/1/1 router-interface ve 30!vlan 40 by port tagged ethe 1/1/1 router-interface ve 40!vlan 100 by port tagged ethe 1/1/1 ethe 1/1/7 untagged ethe 1/1/8 to 1/1/9 router-interface ve 100!!!aaa authentication web-server default localaaa authentication login default localboot sys fl secno ip dhcp-client auto-update enableip dhcp-server enableno ip dhcp-server mgmt!ip dhcp-server pool public dhcp-default-router 172.16.1.1 dns-server 8.8.8.8 excluded-address 172.16.1.1 lease 0 1 0 network 172.16.1.0 255.255.255.0 deploy!!ip dhcp-server pool members dhcp-default-router 172.16.2.1 dns-server 8.8.8.8 lease 0 12 0 network 172.16.2.0 255.255.255.0 deploy!!ip dhcp-server pool media dhcp-default-router 172.16.3.1 dns-server 8.8.8.8 lease 0 4 0 network 172.16.3.0 255.255.255.0 deploy!!ip dhcp-server pool vlan100 dhcp-default-router 10.10.64.1 dns-server 10.10.64.1 8.8.8.8 excluded-address 10.10.64.1 10.10.64.50 lease 1 0 0 network 10.10.64.0 255.255.254.0 deploy!ip default-network 10.10.64.0/23ip dns domain-list CI_LAip dns server-address 10.10.64.1 8.8.8.8ip route 10.10.64.0/23 ethernet 1/2/1ip route 172.16.1.0/24 ethernet 1/2/1!!!!!!!!!!interface ethernet 1/1/1 dual-mode 10!interface ethernet 1/1/3 inline power!interface ethernet 1/1/4 inline power!interface ethernet 1/1/5 inline power!interface ethernet 1/1/6 inline power!interface ethernet 1/1/7 inline power!interface ethernet 1/1/8 inline power!interface ethernet 1/1/9 inline power!interface ethernet 1/1/10 inline power!interface ethernet 1/1/11 inline power!interface ethernet 1/1/12 inline power!interface ethernet 1/3/2 speed-duplex 1000-full!interface ethernet 1/3/4 speed-duplex 1000-full!interface ve 20 ip address 172.16.1.1 255.255.255.0!interface ve 100 ip address 10.10.64.1 255.255.254.0!!interface ve 30 ip address 172.16.2.1 255.255.255.0!interface ve 40 ip address 172.16.3.1 255.255.255.0!!!!!!!end