Posted on 29 May, 2019, in Uncategorized
What DTIM represents and how to change the value
Posted on 25 May, 2019, in Uncategorized
Hello, I have 6 ICX 6450 in a stack. 3 on one floor and 3 on another floor. We’re no longer leasing 1 of the floors and therefore consolidating everything. The 3 switches that need to be moved are acting as the active and standby switches with all others being members. What would be the best way to move these switches?Should I make one of the switches NOT being moved the active switch and reload the stack before unplugging those switches to be moved? Or can I just unplug them and move them without doing anything? Not sure what happens to the stack when it loses both active and standby switches.Any help will be greatly appreciated.
Posted on 24 May, 2019, in Uncategorized
Hi team!I test broadcast/multicast/unknown-unicast limits on ICX7250 and ICX7150 (hw ver. 8.0.9).I’ve configured ports as: interface ethernet 1/1/1 spanning-tree 802-1w admin-edge-port broadcast limit 96 kbps multicast limit 400 kbps unknown-unicast limit 96 kbps stp-bpdu-guardBut, nothing happens! I genarate broadcast traffic, but port works normally in this moment.Can anyone come across this problem?
Posted on 24 May, 2019, in Uncategorized
Hello everybody. I’m trying to have my ICX7150 (08.0.80) working with an external captive portal. My device connected to eth 1/1/11 receives an IP address an if it manually open the captive portal page it works, but … no way to have it displayed automatically or being redirected opening another web site. Where am i wrong? Here’s the config, i’ve follwed online guide (my captive is on Cloudpath): https://ruckus-support.s3.amazonaws.com/private/documents/2478/ruckus-icx-flexible-auth-cloudpath-52-dp.pdf?AWSAccessKeyId=AKIAJM3QLNNKLOV235TQ&Expires=1557155681&Signature=n4NyA9sgP1PNx65c6iBwzc4gDAs%3DThis is my config.Current configuration:!ver 08.0.80dT211!captive-portal cloudpath virtual-ip <myfqdn> virtual-port 443 login-page /enroll/portal/reset!!default-vlan-id 4000!vlan 1 name Management by port tagged ethe 1/2/1 untagged ethe 1/1/1 to 1/1/10 management-vlan default-gateway <A.B.C.D> 1!vlan 75 name Ospiti_DiRete by port tagged ethe 1/2/1 untagged ethe 1/1/11 webauth captive-portal profile cloudpath auth-mode captive-portal trust-port ethernet 1/2/1 enable!vlan 4000 name DEFAULT-VLAN by port!aaa authentication dot1x default radiusaaa authorization coa enableaaa accounting dot1x default start-stop radiusaaa accounting mac-auth default start-stop radiusip address <A.B.C.D> 255.255.255.0ip dns domain-list domain.localip dns server-address <A.B.C.D>!logging console!radius-client coa host <A.B.C.D> key <key>!web-management https!interface ethernet 1/3/1 speed-duplex 1000-full!interface ethernet 1/3/2 speed-duplex 1000-full!end
Posted on 24 May, 2019, in Uncategorized
Ruckus Diagnostic Dashboard (RDD) is a lightweight tool that helps automate the troubleshooting and support process. RDD provides a single pane of glass view for Ruckus Support. Here you will find all the latest information on RDD releases, interact with the Product Management, and Support teams.
Posted on 24 May, 2019, in Uncategorized
I would like to stack some 6450s in with some 7450 stacks. Is there any reason why this would not be possible?
Posted on 24 May, 2019, in Uncategorized
I have one DHCP server in default VLAN. I have multiple VLAN (voice) and I want the ports on the VLAN to grab dhcp addresses from additional scopes. I know that I need to use IP Helper, but all instructions refer to an IP address assigned to your VLAN. I don’t see where to do that…only IP address assigned is the siwtches IP.
Posted on 24 May, 2019, in Uncategorized
Switch will not power up. No LEDs no humming. Nothing. Is there any way to bring this back to life? Or is it just dead?
Thx,
Scott
Posted on 24 May, 2019, in Uncategorized
Good morning,I have 2 ICx 7150 switches in stack.This is my configCurrent configuration:!ver 08.0.80dT211!stack unit 1 module 1 icx7150-48p-poe-port-management-module module 2 icx7150-2-copper-port-2g-module module 3 icx7150-4-sfp-plus-port-40g-module stack-port 1/3/1 1/3/3stack unit 2 module 1 icx7150-48p-poe-port-management-module module 2 icx7150-2-copper-port-2g-module module 3 icx7150-4-sfp-plus-port-40g-module stack-port 2/3/1 2/3/3stack enablestack mac d4c1.9e26.4c9bstack suggested-id 1!!!!!vlan 1 name DEFAULT-VLAN by port!vlan 100 name XXX by port tagged ethe 1/1/25 ethe 1/1/37 to 1/1/48!vlan 105 name XXX_VOIP by port tagged ethe 1/1/48 untagged ethe 1/1/25!vlan 125 name XXX_MANAGEMENT by port tagged ethe 1/1/48 untagged ethe 1/1/37 to 1/1/46!!!!!!!!!!!!!aaa authentication web-server default localaaa authentication enable default localaaa authentication login default localaaa authentication login privilege-modeenable super-user-password …..hostname XXX_SW01_LABip address 172.31.253.241 255.255.255.0ip default-gateway 172.31.253.254!username admin password …..cdp runfdp run!!clock timezone gmt GMT+01hitless-failover enable!!sz active-list 192.168.100.192 83.216.184.111!!!!lldp run!!!!!endI have 3 VLANs100 – Date105 – VoIP125 – MGMTOn the 1/1/25 port (Vlan 105) I attached a VoIP phone (SNOM) that correctly takes an IPIn fact, through the “sh lldp neighbors” command I see itHow can I make the other phone’s port release an IP of the VLAN 100 to be able to connect a PC (The Dual-Mode command is disabled)? Thank you
Posted on 24 May, 2019, in Uncategorized
I’m looking for a letter of volatility for the ICX-7150-C12P. I need this letter before I can connect this switch to the company lab network.
Posted on 24 May, 2019, in Uncategorized
Good evening to all, I would have a problem on a Ruckus ICX7150-48P-4X10GR switch installed in the company where I work, in some cases it involves connecting to ssh.Initially we had no problem connecting to ssh, for about two weeks it has happened that trying to connect in ssh we have this error (I add stamp).Receiving this error is as if there were no more sessions available for the ssh connection, connecting to the console giving the “sh who” command we actually see that the ssh sessions are almost all closed and therefore available.The solution to this problem is to wait a few minutes (usually 10-15) to be able to connect again.Has anyone like this happened to anyone?The version mounted on the switch isSW: Version 08.0.80dT211Thank you in advance
Posted on 24 May, 2019, in Uncategorized
Hello everyone,I apologize if my question may seem silly, but I have to configure a ICX 6430-48 switch and I followed the procedure in the instruction manual, so I connected with the hyperterminal using the console cable, I set an IP address, I created a local user, and I activated the web-management … but when I try to connect via the net with http I can log in but I only get the image of the switch with the LEDs that give me real time the activity of the switch itself (I tried with various browsers and also with different operating systems, and it doesn’t change anything). Why doesn’t the menu appear to configure the switch via the web? Could it be that there is some problem with the license? Or is there any other passage to do?Thank you all, and sorry again for the banality of my questions.FrancescoP.S. I have attached the screenshot of the web page that appears to me.
Posted on 24 May, 2019, in Uncategorized
I new at Brocade and I have ICX 7450-24p with 3 module fiber.=====telnet@DIST-BRU(config)#show running-configCurrent configuration:!ver 08.0.30hT211!stack unit 1 module 1 icx7450-24-port-management-module module 2 icx7400-xgf-4port-40g-module module 3 icx7400-xgf-4port-40g-module module 4 icx7400-xgf-4port-40g-module!!=====I can’t active “rip” and don’t finded router-interface, that switch is L2?
Posted on 24 May, 2019, in Uncategorized
This seems like a very simple configuration, wondering what may have changed to make it not work intuitively. Trying to get our 7850s stood up in the lab, these are the 48Fs, so the 1/10/25G ports on module 1.I can’t seem to get the 1G links to connect to either a 7450’s 1/10 ports on module 2 or a 7750’s 1/10 ports on module 1. The 7850 shows up but the 7450 and 7750 shows down. Is there something in the configuration I’m missing?7850:GCB-LAB-IR(config)#sho int e 1/1/525GigabitEthernet1/1/5 is up, line protocol is up Port up for 58 second(s) Hardware is 25GigabitEthernet, address is 94bf.c43e.e6d8 (bia 94bf.c43e.e6dc) Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx Configured mdi mode AUTO, actual MDI Untagged member of L2 VLAN 4002, port state is FORWARDING BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0, mac-learning is enabled Openflow is Disabled, Openflow Hybrid mode is Disabled, Flow Control is config enabled, oper not supported, negotiation disabled Mirror disabled, Monitor disabled Mac-notification is disabled VLAN-Mapping is disabled Not member of any active trunks Not member of any configured trunks No port name IPG MII 96 bits-time, IPG GMII 96 bits-time MTU 9380 bytes, encapsulation ethernet MMU Mode is Store-and-forward 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 300 second output rate: 824 bits/sec, 1 packets/sec, 0.00% utilization 2 packets input, 180 bytes, 0 no buffer Received 0 broadcasts, 2 multicasts, 0 unicasts 0 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 104 packets output, 13419 bytes, 0 underruns Transmitted 0 broadcasts, 104 multicasts, 0 unicasts 0 output errors, 0 collisions Relay Agent Information option: Disabled Protected: No MAC Port Security: DisabledUC Egress queues:Queue counters Queued packets Dropped Packets 0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 19 0 8 0 0 9 0 0MC Egress queues: Queue counters Queued packets Dropped Packets 0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 85 0 6 0 0 7 0 0 8 0 0 9 0 0Oversubscribed ingress drop counters:High priority drop 0Low priority drop 0Total drop 0GCB-LAB-IR(config)#sho run int e 1/1/5interface ethernet 1/1/5 speed-duplex 1000-full7450:SSH@PL1B-B111-1>sho int e 1/2/310GigabitEthernet1/2/3 is down, line protocol is down Port down for 8 day(s) 15 hour(s) 47 minute(s) 15 second(s) Hardware is 10GigabitEthernet, address is 609c.9f31.39d3 (bia 609c.9f31.39d3) Configured speed 1Gbit, actual unknown, configured duplex fdx, actual unknown Configured mdi mode AUTO, actual unknown Untagged member of L2 VLAN 4002, port state is DISABLED BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0, mac-learning is enabled Flow Control is config enabled, oper enabled, negotiation disabled Mirror disabled, Monitor disabled Mac-notification is disabled VLAN-Mapping is disabled Not member of any active trunks Not member of any configured trunks No port name IPG XGMII 96 bits-time MTU 10200 bytes MMU Mode is Store-and-forward 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 multicasts, 0 unicasts 0 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 0 packets output, 0 bytes, 0 underruns Transmitted 0 broadcasts, 0 multicasts, 0 unicasts 0 output errors, 0 collisions Relay Agent Information option: Disabled Protected: No MAC Port Security: DisabledUC Egress queues:Queue counters Queued packets Dropped Packets 0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0MC Egress queues:Queue counters Queued packets Dropped Packets 0 0 0 1 0 0 2 0 0 3 0 0SSH@PL1B-B111-1>sho run int e 1/2/3interface ethernet 1/2/3 speed-duplex 1000-fullPort 1/2/3: Type : 1G M-LX(SFP)Same optics, tried LX and SX, same result on all.
Posted on 24 May, 2019, in Uncategorized
We’ve used ICX-7750 switches for a while to support fiber links to all of our campus wings but now we are looking to use the devices to replace our aging router for each school. We were able to configure the port 1 for our WAN link and port 2 for our LAN side and routing everything correctly (we only use simple RIP routing) but ports 20 through 48 go out to our wings that are on the same LAN as port 2. I’m sure there is a simple way to bridge these ports, I’m just not familiar enough with the router software to know how to do it.Any assistance is greatly appreciated